11/9/2021 0 Comments Tự Học Mastercam X4 Mill
Teen madam.Đây là hướng dẫn sử dụng phần mềm Mastercam-X4. His shows young x 4 takes chessie with a. Foxxxxxxxxy vergon 13 factory mizuho submission masturbation latina indian. Trong video c&243 c&225 c c&244 ng c ca phn mm t thit k, lp tr&236 nh phay 2D, lp tr&236 nh phay 3d, c&225 c file thc h&224 nh v&224 b&224 i tp i k&232 m nhm gi&250 p ngi hc h thng c&225 c c&244 ng vic m&224 m&236 nh s l&224 m thc t. Hng dn ho&224 n chnh phn phay 2d v&224 3d tr&234 n mastercam x4.
Tự Học Mastercam X4 Mill Software Described InManual is sold orlicensed "as is." The entire risk as to its quality and performance is with the buyer. Makes no warranties, either express or implied, with respect to thismanual or with respect to the software described in this manual, its quality, performance,merchantability, or fitness for any particular purpose. Reserves the right to make improvements to this manual at any time andwithout notice.Disclaimer of All Warranties and LiabilityIn-House Solutions Inc. - All rights reserved.Software: Mill Mastercam X4Author: Mariana LendelISBN: 978-1-92NoticeIn-House Solutions Inc.This document may not, in whole or part, be copied, photocopied, reproduced,translated or reduced to any electronic medium or machine-readable form without priorconsent, in writing, from In-House Solutions Inc.TrademarksMastercam is a registered trademark of CNC Software, Inc.Microsoft, the Microsoft logo, MS, and MS-DOS are registered trademarks of MicrosoftCorporation Mastercam Verify is created in conjunction with Sirius Systems Corporation Windows 95, Windows NT and Windows XP are registered trademarks of MicrosoftCorporation.Acknowledgements"Thanks to the In-House Solutions team for helping in the production and marketing of thisbook. Somejurisdictions do not allow the exclusion or limitation of implied warranties or liability forincidental or consequential damages, so the above limitation or exclusion may not apply to you.CopyrightsThis manual is protected under the copyright laws of Canada and the United States. Has been advised of the possibility of such damages. In no event will In-House Solutions Inc.be liable for direct, indirect, or consequential damages resulting from any defect in the manual,even if In-House Solutions Inc.An alphabetic description of the 2D toolpath parameters,of the Solid menu and Operations Manager are also covered in the General Notes.Each tutorial walks you through all the procedures from Geometry Creation to Toolpathinstructions, Verification and G-Code Generation.LEGEND:Step to follow to complete the tutorialAdditional explanation for the current step or warnings.Callouts that give direction on how to complete the taskCallouts that describe the parameters used in the current step: Mastercam promptsBold text (usually) represents Mastercam terminologyTABLE OF CONTENTSGetting Started A1Graphic User Interface. Explanations are given for the use of WCS in multiple fixture applications aswell as proper Stock Setup and Tool Settings.The Mill Training Tutorials also include a General Notes chapter with useful tools and shortcutsthat make the software easier to use. It also contains 2D High Speed Toolpaths and FeatureBased Machining. Itcontains pages of projects, helpful hints, as well as tool and material library instructions.The book covers ten part projects in all and an additional 17 exercises.The material covered includes 2D Geometry and Solids Creation, Drilling, Tapping, Contouring,Pocketing, Circle Milling and Slot Milling. Finally, thank you, the reader formaking this purchase I hope it serves you well."Mariana LendelTUTORIAL SERIES FORHOW TO USE THIS BOOKThis book provides a comprehensive step by step approach to learning Mastercam Mill. 4-1Tutorial #5, 2D Geometry, Dynamic Mill & Transform Toolpaths 5-1Tutorial #6, 2D Geometry, Pocket with an Island & Circle Mill 6-1Tutorial #7, 2D Geometry, Using WCS, Facing, Drilling, Pocketing, Contour 7-1Tutorial #8, 2D & Solids Geometry, Machining the part using WCS. 3-1Tutorial #4, 2D Geometry, Drill, Slot Mill & 2D HS Core Mill. A-4Setting the Grid A-6TUTORIALS 11Tutorial #1, 2D Geometry, Open Contour and Drilling 1-1Tutorial #2, 2D Geometry, Drill, Open Pocket, Open Contour and Chamfer 2-1Tutorial #3, 2D Geometry, Tapping, Contouring, Pocketing and Save Operations. C-6TUTORIAL SERIES FORTUTORIAL #7LEVEL 1 – 3D WIREFRAMEUSING WCS, FACING, CONTOURING, POCKETING, DRILLING,IMPORT FROM LIBRARY.Mill Level 1Objectives:The Student will design a 3-dimensional wireframe drawing by:Creating a rectangle.Creating parallel lines.Creating fillet radii.Creating arcs knowing the center location and the diameter.Creating an arc tangent to three entities.Using Translate to create a 3-dimensional wireframe.The Student will create a 2-dimensional milling toolpath consisting of:First SetupFacing the bottom of the part for an even surface.Importing from the library 9/16 tap holes.Drilling 3/8 holes.Second SetupFacing the top of the partMachining simultaneous two pockets with different depths.Circle milling the 2.0“ hole.Machining a 2D contour.The Student will check the toolpath using Mastercam’s Verify module by:Defining a 3-dimensional rectangular block the size of the workpiece.Running the Verify function to machine the part on the screen.-2TUTORIAL 7. B-47Milling G-Codes B-50Creating or Editing a Tool in the Library C1Create a New Tool C-1Edit an Existing Tool. B-36Window Selection B-39Chaining and Window Options B-40Toolpaths Manager B-42Properties. B-102D HS Specific Parameters B-23Create Geometry in 3D B-28Solids Menu B-33Solids Manager. B-2Customizing B-3Key Mapping B-7Data Entry Shortcuts B-92D Toolpath Parameters. Facebook sai baba 53 episodeTUTORIAL 7 : Hold-down the Shift key and select Entity C Note that the entire pocket should be highlighted Select Entity C Select the End Selection button Change the Delta value on Z to -0. Select Entity E Select Entity C here Select Entity E here Select Entity D here Select the Repaint button Select the OK button -1 9 Mill Level 1 TUTORIAL 7 STEP 6: CREATE THE 3-D WIREFRAME Step Preview: Xform Select Entity A Translate : Hold-down the Shift key and select Entity A as shown Note that the entire rectangle should be highlighted Otherwise, please check the. 375 Select the Apply button to continue -2 1 Mill Level. Entity]: Select Entity A Select Entity B here Select Entity C here Select Entity A here Select Entity D here Select Entity F here Select Entity E here Select the OK button to exit fillet command -1 2 Mill Level 1 TUTORIAL 7 STEP 5: CREATE THE RIGHT SIDE POCKET Step Preview: 5.1 Create parallel lines Sub Step Preview: Create Line Parallel : Select Entity A : Select Entity A : Pick a point above the selected line Type the Distance 1.0 + 4.
0 Comments
Leave a Reply. |
AuthorVeronica ArchivesCategories |